Easy Ways to Propagate Rubber Plants (Ficus Elastica)
Read in: 4 min
Read in: 4 min
Propagating Rubber Tree Plants (Ficus Elastica) is easy and can be done via:
Stem cuttings in potting mix or water
Leaf cuttings
Air layering
Seed germination (advanced technique)
Once you’ve started propagating your Rubber Plant, you’ll start to see roots within 3 to 4 weeks and it will be ready for a pot within 2 to 4 months.
This makes it a perfect project in the summer if you want to give your friends and family a plant gift for the holidays, in the fall if you want something unique for a Galentine’s or Palentine’s celebration gift.
Knowing the time to potting them also lets you plan ahead if you want to add a Ficus or two to your gardens outdoors if you live in tropical and subtropical climates like Florida or Southern California. Make sure to check your local city and state’s websites to ensure it isn’t prohibited as Ficus can strangle other plants and may be considered an invasive species.
Fun fact: Some Ficus Elastica are now cultivated to withstand all four seasons (but can still be damaged by frost) making them able to survive year round outdoors in more mild winters instead of requiring tropical climates like their native Southeast and South Asian homes.
If you’re ready to propagate your Ficus Elastica, here’s the steps and what you’ll need for each of the four methods.
To propagate your Rubber Tree in potting mix or water via a stem cutting, you will need:
A container to host the propagating plant
A pot with holes to drain excess moisture for potting mix or soil propagation
A container no holes for water propagation
Sterilized shears
Potting mix or filtered water
To propagate via stem cuttings:
Fill the pot or container with potting mix or water.
Trim a stem with about 6 inches of branch visible with the sterilized shears.
Trim off any leaves close to the bottom while leaving higher up ones on the stem.
Place the lower 2 to 3 inches in the potting mix or water.
Let it sit for 3 to 4 weeks until a strong root system has developed.
Move the new plants to a pot with a potting mix that is airy and moisture retaining.
Leaf cutting propagation is very similar to stem, except instead of a larger stem you only want one leaf and one node. The stem can be shorter than the six inch mark at more of a single inch which lets you use a smaller container or pot.
Pro-tip: When propagating in water, watch for the roots and submerged step to get soggy and change to a brown or murky color, this is a sign of root rot.
This Rubber Plant propagation technique uses a mature plant to create a new one by wounding a stem instead of cutting a leaf or stem off which encourages new roots to grow. Once this happens they can be potted or planted making it a resource friendly propagation technique.
You will need:
One sterilized pair of shears, razor blade, or box cutter
Sphagnum moss that is damp with filtered water
A plastic bag or plastic wrap (it needs to be clear)
One rubber bands, zip tie, or twisty tie
One match stick without the part that catches fire or a thin item of similar size and width
To air layer:
Take a large and mature stem at least 12 inches away from the tip of the branch and trim off any leaves where you intend to make the cut.
Cut a slit at a 45 degree angle halfway through the branch making sure not to go deeper right below the node.
Prop the slit open with the thin item (the match stick) so the wound does not heal itself and the roots can grow.
Wrap the sphagnum moss around the wound so it is fully covered.
Place the plastic bag around the sphagnum moss or wrap it in the see through plastic wrap so everything holds in place and the moisture is retained.
Keep the moss moist by adding water when it dries out until a root system forms. This can take 4 - 10 weeks.
Trim the new plant off so the roots stay with the new one and plant it in a pot or your garden.
This is the most difficult as the plant rarely produces seeds, and when it does the seeds need to be carried through a labor intensive and time consuming process. But it is a good one if you have access to a mature Ficus Elastica plant that has bloomed, or seeds, and a high humidity environment that mimics spring or summer when they would normally begin to germinate and grow.
You will need:
Rubber plant seeds
A tray with a cover to retain humidity
A moisture retaining and airy potting mix or material
Filtered water
To propagate by seed:
Take the potting mix and place it in a tray that can be covered.
Place the seeds in the potting mix.
Moisten the potting mix with the filtered water.
Keep the temperature in the container around 70–79°F (21–26°C) and the potting mix roughly 77–83°F (25–28°C)
The seeds should begin to germinate within 1 - 3 weeks (in a perfect scenario), but they are dormant so the time could be longer as they need to leave the dormant state.
Once they have germinated and roots are long enough an inch or two, transfer them to a pot and plant them.
Propagating a Rubber Plant is easy and fun. It’s easy to do via stem and leaf cuttings, or air layering. If you’re patient and lucky enough to find Ficus Elastica seeds, it can be rewarding to try germinating them and watching the process. And once your plant has grown, here’s our guide to caring for Ficus Elastica Rubber Tree plants.